Rack 18 — Full guide
How Rack 18 works and everything it does, screen by screen. For app version 2.0.
CONTENTS
01
Before you start
Rack 18 controls Midas MR18 and Behringer XR18 / X18 digital mixers from an iPhone, iPad, or Android phone or tablet, over Wi-Fi. It needs no account and sends nothing to the internet: it talks only to the mixer on the local network.
- —Phones show the app in landscape. Tablets work in any orientation: held sideways, the mixer screen shows all 16 input channels at once; held upright, every other page appears with the mixer below it.
- —The app follows the device language: Greek on a device set to Greek, English otherwise. Mixer terms (GAIN, EQ, MUTE, SOLO, BUS, FX, SEND, LOW CUT…) stay as they are printed on the hardware.
- —DEMO, on the connect screen, runs a software mixer, so you can explore every screen without hardware.
- —Every change is sent to the mixer straight away. What lives in the app (scenes, setlists, your own presets, musician mode, recent mixers) is kept on this device only.
02
Connecting to the mixer
The REMOTE switch on the mixer decides which way it listens. Use one of the three ways below; HOW TO CONNECT? on the connect screen shows the same steps.
Mixer Wi-Fi
- —REMOTE switch to ACCESS POINT.
- —On the phone, join the mixer's own Wi-Fi network (its name starts with the model, e.g. MR18-…), come back to the app and tap CONNECT.
- —Nothing else to carry. The range is that of the mixer's small antenna.
Router (best for live)
- —REMOTE switch to ETHERNET, and a cable from the mixer's ETHERNET port to the router.
- —Join the router's Wi-Fi network and tap CONNECT.
- —The best range and the most stable link. Several phones and tablets can work at the same time.
Phone hotspot
- —Once: connect one of the other ways and save your hotspot name and password to the mixer in TOOLS › HOTSPOT (see Hotspot below).
- —Turn the phone's hotspot on (2.4 GHz, WPA2-Personal), set the REMOTE switch to WIFI CLIENT, wait up to a minute and tap CONNECT.
- —No router, and the phone keeps its mobile internet. It uses the phone's battery.
The connect screen
- —NETWORK SCAN looks for mixers by itself. A mixer that is found shows its name, model, address and firmware: tap CONNECT. With several mixers, tap a card to choose one.
- —MANUAL IP: type the mixer's address and tap GO. Mixers you have used appear under RECENT.
- —DEMO opens the software mixer.
- —On iPhone and iPad the app needs the Local Network permission. If it is off, the screen says so: turn on Settings › Privacy & Security › Local Network › Rack 18.
While connected
- —The display at the top of the mixer screen shows the link: CONNECTING…, then SYNC with a percentage while the app reads the mixer, then the model with ONLINE and the mixer's address.
- —The app keeps the link alive on its own and reconnects after Wi-Fi drop-outs (RECONNECTING…).
03
The mixer screen
The main screen looks like the mixer itself: a row of channel strips, the master strip, and a column of buttons on the right.
Top bar
- —SCENE display: the number and name of the snapshot loaded on the mixer.
- —Connection display: the link state; tap it for SETUP.
- —Buttons: REC (the recorder; while it records it blinks and shows the time), METERS, RACK (effects), SNAP (snapshots), SCENES, ROUTING, TOOLS, SETUP.
Channel strips
- —At the top, the channel's colour and name as set on the mixer. Tap the name to open the channel page (DCA strips have no page).
- —Pan: drag the row of LEDs. While you pan, the strip's display shows the pan position.
- —SOLO and MUTE.
- —The fader with its level meter; the display above it shows the level in dB. Double-tap a fader to set it to 0 dB.
Layers
- —CH 1–8 and CH 9–16: the 16 input channels.
- —AUX · FX RETURNS: the AUX IN and the returns of the 4 effects.
- —BUSES 1 – 6: the 6 buses (monitor mixes).
- —FX SND MASTERS: the master levels of the 4 effect sends.
- —DCA GROUPS: the 4 DCAs.
- —On a tablet held sideways, one CH 1–16 button shows all 16 inputs side by side; held upright, CH 1–8 sit above CH 9–16.
Master strip
- —Normally MAIN LR: the main stereo mix, with balance.
- —BUS MASTER switches it to the master of the current send target (a bus or an FX send), and back.
Buttons on the right
- —FINE: faders and knobs move 4× more precisely.
- —MUTE GROUPS: the mixer's 4 mute groups, one tap each. Which channels belong to each group is set on the MAIN tab of each channel.
- —SENDS ON FADER: the faders become the send levels to the chosen target instead of the main mix. The level displays turn yellow and the title shows SENDS → and the target.
- —SEND TARGET: choose where the faders send: BUS 1–6 or FX 1–4. Choosing a target also turns SENDS ON FADER on.
- —LOCK TOUCH: locks the faders, knobs and buttons that change the mix against accidental touches; tap again to unlock. Changing layer and screen still works.
04
The channel page
Tap a strip's name to open its page. The strip itself stays on the left; at the top are MIXER (back), the name, PREV / NEXT and the tabs.
- —PREV / NEXT go through every strip in order: CH 1–16, AUX, FX 1–4 returns, BUS 1–6, FX SEND 1–4, MAIN LR.
- —Tabs: input channels have INPUT, GATE, EQ, DYN, SENDS, MAIN · AUX and FX returns have EQ, SENDS, MAIN · buses and MAIN LR have EQ, DYN, MAIN · FX sends have MAIN.
- —Input channels also have PRESET (instrument presets, see Tools) and COPY / PASTE, which copies low cut, gate, EQ and compressor from one channel to another (not gain, name, routing or sends).
- —Double-tap any knob to return it to its default value.
INPUT
- —GAIN of the preamp (inputs 1–16) with its level meter; for the line input (SRC 17 / 18) a LINE IN TRIM.
- —+48V phantom power asks for confirmation first: only for condenser mics and active DI boxes, and mute the channel before.
- —Ø INVERT (polarity), LOW CUT and LC FREQ.
- —AUTO GAIN › sets this channel's gain while the band plays (see Tools).
- —STEREO LINK: LINK CH 1 + 2 and so on. Linked channels share their settings.
- —SOURCE: ANALOG IN, with the input to use (IN 01–16, SRC 17 (L), SRC 18 (R) or OFF), or USB RETURN, with the USB channel (USB 01–18) and USB TRIM, for a virtual soundcheck from a computer.
- —SIGNAL CHAIN on the right: LOW CUT, GATE, EQ and COMPRESSOR on or off, and the fader level. Tap a stage to open it.
GATE
- —GATE ON and the mode: GATE, EXP 2 / EXP 3 / EXP 4 (expander 1:2, 1:3, 1:4) or DUCK (lowers the channel while the key signal is above the threshold).
- —THRESHOLD, RANGE, ATTACK, HOLD, RELEASE.
- —KEY FILTER (ON, type, frequency) and the key source: SELF, any channel CH 01–16, or BUS 1–6.
DYN (compressor)
- —COMP ON; COMP or EXP; PEAK or RMS detection; LIN or LOG envelope; AUTO TIME (automatic attack and release).
- —THRESHOLD, RATIO (1.1 to 100), KNEE, GAIN, ATTACK, HOLD, RELEASE, MIX.
- —KEY FILTER and key source, as on the gate (on MAIN LR the key is the main signal itself).
- —INSERT FX: puts one of the rack's effects on this strip as an insert (ON, and the slot).
SENDS
- —One fader per send, with its level in dB: BUS 1–6 (monitor mixes) and FX 1–4 (effect sends).
- —Under each send, its tap point: IN, PRE EQ, POST EQ, PRE, POST or GRP.
- —When two buses are linked as a stereo pair, the send to them also gets a PAN.
MAIN
- —TO MAIN LR: whether the strip goes to the main mix; PAN (BALANCE on MAIN LR).
- —DCA GROUPS (1–4, with their names) and MUTE GROUPS (1–4): tap to add or remove the strip.
- —NAME & COLOUR: tap the name to type a new one; 16 colours (top row lit, bottom row dark with coloured text).
- —Input channels: AUTOMIX group (OFF, X or Y) and WEIGHT. Automix balances the open mics of a group by itself.
- —Buses: STEREO LINK of the pair (LINK BUS 1 + 2 and so on), for a stereo in-ear mix.
- —MAIN LR: the main bus feeds MAIN OUT L/R (XLR) and, by default, the phones output; OUTPUT ROUTING opens the routing.
05
EQ and analyser
Input channels, AUX and FX returns have a 4-band parametric EQ. Buses and MAIN LR have a 6-band EQ that can also work as a 31-band graphic EQ.
- —EQ ON switches the EQ on or off. On input channels, LOW CUT and its frequency are here as well.
- —The band buttons select a band. For each band choose its type: L-CUT, L-SHV, PEQ, VEQ, H-SHV, H-CUT (low cut, low shelf, parametric, vintage, high shelf, high cut).
- —On the curve: drag a point left and right for the frequency, up and down for the gain. Put a second finger down and pinch to change the width (Q). Double-tap a point to set its gain back to 0 dB. Touch away from the points and the selected band moves. Drag the tab at the top of the dashed line to move the low cut.
- —The FREQ, GAIN and Q knobs do the same for the selected band. RESET BAND sets its gain to 0 dB and its width back to the default.
- —COPY EQ / PASTE EQ (input channels) copies the EQ from one channel to another.
- —Buses and MAIN LR: choose the EQ mode, PEQ, GEQ or TEQ. In GEQ and TEQ the page shows 31 sliders from 20 Hz to 20 kHz, ±15 dB: drag a slider, double-tap it for 0 dB; FLAT (ALL 0 dB) resets all 31 after confirmation.
- —RTA shows the mixer's real-time spectrum behind the curve or the sliders. POST EQ measures after the EQ instead of before it. FOLLOW makes the analyser follow the strip on screen.
06
FX rack
RACK opens the mixer's 4 effect processors, each drawn as a rack unit.
- —CHANGE: choose the effect by category: REVERB, DELAY, MODULATION, MULTI, PITCH, DYNAMICS, EQ, ENHANCE, GUITAR · DRIVE. All 61 effects of the mixer, each with a picture of its face; the one loaded is marked.
- —The knobs on the face control the main parameters. EDIT opens every parameter of the effect, on pages.
- —TAP, on effects with a delay: tap in time and the delay time follows (the app shows ms and BPM).
- —RETURN: the effect's return level (drag it). The SIG and CLIP lights show signal and overload.
- —Some faces have a pilot lamp: tap it to switch the effect on or off.
- —At the bottom, each unit shows whether it is fed from its FX SEND or is used as an insert on a channel.
- —Graphic EQ effects: EQ A / EQ B on the dual versions, and FLAT.
The 61 effects
- —REVERB (10): Hall Reverb, Ambience, Rich Plate Reverb, Room Reverb, Chamber Reverb, Plate Reverb, Vintage Reverb, Vintage Room, Gated Reverb, Reverse Reverb.
- —DELAY (4): Stereo Delay, 3-Tap Delay, Rhythm Delay, Modulation Delay.
- —MODULATION (7): Stereo Chorus, Stereo Flanger, Stereo Phaser, Dimensional Chorus, Mood Filter, Rotary Speaker, Tremolo / Panner.
- —MULTI (5): Delay / Reverb, Chorus / Reverb, Flanger / Reverb, Delay / Chorus, Delay / Flanger.
- —PITCH (2): Dual Pitch, Stereo Pitch.
- —DYNAMICS (13): Dual De-esser, Stereo De-esser, Wave Designer, Precision Limiter, Stereo Combinator, Dual Combinator, Stereo Fair Compressor, M/S Fair Compressor, Dual Fair Compressor, Stereo Leisure Compressor, Dual Leisure Compressor, Stereo Ultimo Compressor, Dual Ultimo Compressor.
- —EQ (8): Dual Graphic EQ, Stereo Graphic EQ, Dual TruEQ, Stereo TruEQ, Stereo Xtec EQ1, Dual Xtec EQ1, Stereo Xtec EQ5, Dual Xtec EQ5.
- —ENHANCE (8): Sub Octaver, Dual Enhancer, Stereo Enhancer, Dual Exciter, Stereo Exciter, Stereo Imager, Stereo Edison EX1, Sound Maxer.
- —GUITAR · DRIVE (4): Dual Guitar Amp, Stereo Guitar Amp, Dual Tube Stage, Stereo Tube Stage.
07
Snapshots and scenes
SNAP: snapshots in the mixer
- —The mixer's own 64 snapshot memories. Tap one to select it.
- —LOAD (after confirmation: the whole mix changes to that snapshot), SAVE (give it a name, up to 31 characters; an existing one asks to OVERWRITE) and DELETE (removes it from the mixer).
- —The SCENE display on the main screen shows which snapshot is loaded.
SCENES: the whole mix, saved on this device
- —SAVE CURRENT MIX reads the whole mix from the mixer (with a percentage) and keeps it on this device under a name: channels, EQ, dynamics, sends, FX and routing.
- —LOAD sends it back to the mixer after confirmation; DELETE removes it from the device.
- —Loading never changes +48V: phantom power stays as it is.
- —Scenes are kept on the device, not in the mixer, so you can load one on another mixer too.
08
Routing
ROUTING has four tabs.
- —OUTPUTS: the source of MAIN and PHONES (MAIN LR, MONITOR = what you solo, or a USB pair playing from a computer or phone, straight to the output), and the source and tap point of AUX 1–6. Tap points marked +M follow the channel mute. By default AUX n carries BUS n.
- —USB SENDS: what the mixer sends to a computer or phone over USB, for each of USB 01–18, with source and tap point.
- —ULTRANET: the 16 outputs P16 01–16, for personal monitor systems.
- —INPUTS: for each channel, its analog input, and a USB button that makes the channel play from USB.
- —While REC records, it uses USB 01/02 and puts them back as they were afterwards.
09
Meters
METERS shows every level at once: channels, AUX, FX returns, buses, FX sends and main; preamps and line in; aux outputs, main outputs and the 18 USB sends to a computer or phone; and the gain reduction of the gates and compressors of channels 1–16.
10
Recording (REC)
REC records straight from the mixer to the phone or tablet through the mixer's USB port, without a computer. The result is a stereo WAV file (16-bit, at the mixer's rate, 44.1 or 48 kHz).
Cable (WHICH CABLE? in the app shows the same)
- —The mixer's USB port is the square one (USB-B, like a printer's).
- —iPhone 15 and later, and iPads with USB-C: one USB-C to USB-B cable.
- —iPhone / iPad with Lightning: Apple's Lightning to USB Camera Adapter plus a USB-A to USB-B cable (an ordinary printer cable). Plain Lightning to USB-C charging adapters usually do not work.
- —Android: one USB-C to USB-B cable; older phones with micro-USB need an OTG adapter (micro-USB to USB-A) plus a USB-A to USB-B cable. The phone must support USB OTG (most do).
- —The mixer runs on its own power, so the phone does not have to power it.
What to record
- —MAIN LR: the stereo mix of the PA.
- —Or a bus: BUS 1–6 one at a time, or a linked pair (e.g. BUS 1+2 · STEREO) in stereo. A single bus is written on both sides of the file.
- —The source is taken after its fader (post-fader).
Recording
- —The app must be connected to the mixer (Wi-Fi or router) and the USB cable plugged in: the app routes the source to USB 01/02 only while it records, and afterwards puts the previous USB routing back, even after an app restart.
- —MIXER USB AUDIO: 18 CH (multitrack to a computer) or 2 CH (stereo, works with every phone). If the phone cannot open 18 channels, the app says so: tap 2 CH, then REC again. If the phone does not see the change, unplug and replug the USB. Switch back to 18 CH here before multitrack recording on a computer.
- —The big button starts and stops the recording. While it records you see the time, the L / R level bars with CLIP, and the source; the REC button on the main screen blinks and shows the time.
- —The free space on the device is shown in hours and minutes.
- —It keeps recording with the screen off. On Android a notification is shown while it records.
- —The source and the USB mode cannot be changed during a recording.
- —Very long recordings continue in a new file (part 2…) before the 4 GB WAV limit. If storage runs out, the recording stops cleanly.
Files
- —Each file is named Rack18 with the date, time and source, e.g. Rack18 2026-11-04 21.30.05 MAIN LR.wav. Recordings made in the same minute are all kept.
- —RECORDINGS, on the right: ▶ plays a recording (on Android in the phone's player; on iPhone / iPad inside the app, through the device's speaker even with the cable connected; stop the recording first) and SEND shares it (mail, messages, cloud…).
- —iPhone / iPad: Files app › On My iPhone (On My iPad) › Rack 18 › Rack 18 Recordings; on a computer, through the device's file sharing (Finder on a Mac, the Apple Devices app or iTunes on Windows).
- —Android: Music › Rack 18 Recordings; on a computer, through USB file transfer.
- —The app records stereo. For an 18-track recording, connect the mixer's USB to a computer with a recording program and keep MIXER USB AUDIO on 18 CH.
11
Tools: feedback, auto gain, instruments
TOOLS gathers six helpers: FEEDBACK, AUTO GAIN, INSTRUMENTS, SETLIST, MUSICIAN MODE and HOTSPOT. The last three have their own sections below.
FEEDBACK (ring-out assistant)
- —Finds ringing in a monitor or the main mix and cuts it. Choose the mix at the top: MAIN or one of BUS 1–6.
- —START, then raise the monitor slowly until it rings. The analyser (after the EQ) shows the spectrum and lists the ringing frequencies.
- —CUT −3 dB next to a frequency cuts it. With AUTO ON, the app cuts by itself.
- —Where it cuts: if the bus EQ is in GEQ or TEQ mode, on the graphic EQ (3 dB steps, up to 9 dB); otherwise with narrow notches on the free bands 2–5 of the 6-band EQ (3 dB steps, up to 12 dB). It never changes the EQ mode.
- —Every cut is listed with UNDO; UNDO ALL CUTS undoes them all.
AUTO GAIN
- —Sets the input gain of every channel from real playing. Choose the target: SAFE, NORMAL or HOT (the loudest peaks at −15, −12 or −9 dBFS).
- —Tap a channel to leave it out. Tap LISTEN and everybody plays and sings as loud as in the show, for 10 seconds (tap to stop earlier).
- —The app proposes a gain for each channel: check it and press APPLY, or DISCARD. UNDO puts the previous gains back.
- —Only the mic preamps (inputs 1–16) are changed, and +48V is never touched. A channel that clipped is lowered and marked CLIPPED · RUN AGAIN; a silent one shows NO SIGNAL.
- —From a channel's INPUT tab, AUTO GAIN › opens it for that channel only.
INSTRUMENTS (presets)
- —Starting points for 14 instruments: VOCAL · MALE, VOCAL · FEMALE, BACKING VOCAL, ACOUSTIC GUITAR, ELECTRIC GUITAR, BASS, KEYS · PIANO, SAX · BRASS, KICK, SNARE, HI-HAT, TOMS, OVERHEADS, PERCUSSION. Fine-tune by ear on the night.
- —A preset sets low cut, EQ and compressor, and turns the gate off. Gain, +48V, fader, pan, sends and routing stay as they are.
- —WHOLE BAND (TOOLS › INSTRUMENTS): tap each channel and choose its instrument, or GUESS FROM NAMES (the app reads the channel names, Greek names too). APPLY sets them all at once, UNDO takes them back, CLEAR ALL empties the choices.
- —One channel: PRESET on its page. SAVE THIS CHANNEL keeps the channel's current settings as your own preset (MINE); UNDO LAST PRESET takes the last one back.
12
Setlist
Your songs in order, each with its own mix. One tap on stage brings the next song's mix.
- —Keep as many setlists as you like: tap the setlist name for NEW, RENAME and DELETE. Deleting a setlist deletes only the list; snapshots and scenes stay.
- —EDIT, then + ADD SONG. For each song: TITLE; MIX FOR THIS SONG (NONE, a MIXER SNAPSHOT, or a SCENE ON THIS PHONE); a NOTE (key, who starts…); TEMPO → FX DELAY TIME (− / +, TAP, OFF).
- —In EDIT you can also move songs up and down, edit them or remove them.
- —On stage: NEXT ▶ goes to the next song and loads its mix; ◀ PREV goes back. Or tap a song to select it, then GO TO SELECTED. NOW PLAYING shows the current song.
- —The tempo sets the delay time of every FX slot holding a delay to one beat, after the song's mix is loaded.
13
Musician mode
Turns a phone into a personal monitor controller: it controls only one monitor mix.
- —TOOLS › MUSICIAN MODE: choose whose mix (BUS 1–6), optionally a 4-digit PIN, then START · BUS and the number.
- —The musician sees the input layers (CH 1–8, CH 9–16, AUX · FX RETURNS) with faders that are the sends to their bus, and the master of their bus. No main mix, mutes, solos, pans, EQ or setup.
- —It stays this way even after the app is closed.
- —To exit: EXIT and the PIN; without a PIN, hold HOLD EXIT for 2 seconds.
14
Hotspot
Lets the mixer join your phone's hotspot: the phone keeps its internet, and other phones can join too.
- —First connect to the mixer through its own Wi-Fi or a router cable.
- —In TOOLS › HOTSPOT, type the hotspot name and password exactly as on your phone (Latin letters, numbers and symbols; name up to 32 characters, password 8 to 63) and tap SAVE TO MIXER. The panel shows how the mixer is set right now.
- —Then, in this order: turn the phone's hotspot on (same name and password, WPA2-Personal, 2.4 GHz, mobile data left on); set the mixer's REMOTE switch to WIFI CLIENT (already there? switch the mixer off and on); wait up to a minute, then CONNECT.
- —The password goes only to the mixer: the app does not keep it.
15
Setup
- —SETUP (or a tap on the connection display) shows the mixer's name, model, firmware, address, the link state and the app version.
- —CLEAR ALL SOLOS; DISCONNECT (back to the connect screen); PANEL FINISH: SILVER or DARK.
- —Reminders: double-tap a fader for 0 dB and a knob for its default; FINE = 4× more precise; LOCK blocks accidental touches.
16
Troubleshooting
- —The mixer is not found: check that the phone is on the mixer's network (not your usual Wi-Fi) and that the REMOTE switch matches the way you connect. On a router, type the mixer's address under MANUAL IP. On iPhone / iPad, allow Local Network for Rack 18.
- —Hotspot not found: the name and password must match exactly (capitals count), 2.4 GHz, WPA2.
- —REC says the phone cannot open 18 USB channels: tap 2 CH, then REC again.
- —REC asks to connect to the mixer first: recording needs both the link to the mixer and the USB cable.
- —If a page cannot be shown, the app says so and offers BACK TO THE MIXER; the mixer itself is not affected.
- —On Android the back button closes windows and returns to the mixer; it never quits the app by accident.
SUPPORT
For questions or technical support, contact info@maistrosmusic.gr
↑ CONTENTS